Pressure Pump
TECHNICAL DATA
- Maximum Operating Pressure - 10 bar
- Maximum Fluid Temperature - 70°C
- Minimum Fluid Temperature - 0°C
- Maximum Ambient Temperature - 50° C
- Mains Connection AC 230 V, 50/60Hz
APPLICATIONS
- Suitable for Liquid Transfer
- Fire Fighting Systems
- Domestic Water Supply
- Industrial Plants
- Washing Systems
- Boiler Feed systems
- Water Treatment Systems
- Pressure Boosting Systems
STANDARD FEATURES
- Highly Reliable
- Silent Operation
- Easy to Carry, Install & Operate
- Stainless Steel Impeller
- Wetted Parts Made of Stainless Steel
- Compact Design
- Wide Performance Range
- Available with Hydro Pneumatic Tank/Electronic Control for Automatic Operation
MATERIAL OF CONSTRUCTION / SPECIFICATION
- Pump Casing: Stainless Steel
- Impeller: Stainless Steel
- Shaft: Stainless Steel
- Mechanical Seal: Carbon / Ceramic
- Pressure Switch: Danfoss Make or Equivalant
- Pressure Tank: MS Powder Coated
SELECTION TABLE
EVACUATED GLASS TUBE SPECIFICATIONS
- Material
- Dimension
- Absorption Coating
- Absorption Capacity
- Emission
- Vacuum
- Stagnation Temp.
- Heat Loss
- Max. Strength
- 1.6mm Borosilicate Glass 3.3
- 58mm x 47mm x 1800mm 58mm x 47mm x 2100mm
- Al - Ni - Cu (Three Layer)
- >92%
- <8% (80° C)
- P<5 x 10-3 Pa
- >200° C
- <0.8 W / 59 M
- 0.8 mpa
FUNCTION
The booster set cuts in and out by means of the pressure switch. when water is tapped from the system, it will at first be tapped from the pressure tank, see below fig. then the pressure falls to the preset cut-in pressure and the pump will cut in. When the water consumption drops, the discharge pressure increases and the pump cuts out when the pressure reaches the preset cut-out pressure of the pressure switch.
Note: This is a typical pressure booster pump system layout. pressures shown in above figures are approximate.
APPLICATIONS
- Pressure Boosting
- Tank Filling
- Water Transfer
- Drip Irrigation
RANGE
- Flow up to 400 m³/hr
- Head up to 200 m
- No of Pumps 2 to 4
- Temperature up to 70° C
MATERIAL OF CONSTRUCTION
- Pump with SS 304 Internals
- Base frame and pipework - MS Zinc Coated
- Other Material of Construction available on request
Eco Green Booster the new generation pressure boosting systems are designed based on state-of-the-art technology offering flexibility to meet all the requirements of pressure boosting in plumbing applications.
The Eco Green Booster systems in specially designed for automatic control of pumps in parallel suitable for fixed speed operation as well as variable speed operation with variable frequency drives for duty and stand-by operation.
The Eco Green Booster system is equipped with a PLC-based controller with a multicolor, compact screen, and user-friendly touch screen with HMI (Human) Machine Interface). Thus offering a very user-friendly controller/input unit for ease of menu navigation and control resulting in simplicity in operation.
PRODUCT/DESIGN FEATURES OF ECO GREEN BOOSTER SERIES:
- Suitable for Eco Green horizontal and vertical in line Booster Pumps.
- Door mounted PLC based Premium automatic controller suitable for up to 4 pumps.
- Maximum Pressure protection in manual mode.
- True case cascading, alteration and stand by functions.
- Selectable test run at selected scheduled timings as required.
- Status of each pump operational data, number of ON/OFF and operating hours.
- Dry run protection by float switches as standard scope of supply and available in manual mode also.
- Factory assembled, compact, reliable and tested system.
- Easy to install, maintain and service locally.
- Low Noise and Vibration level
- High operating efficiency
